ETC Awards Limited · RQF Level 2
ETCAL Level 2 Diploma in Performing Engineering Operations (Northern Ireland)
You don’t just earn this. You learn to use it, one-to-one, on your own real work.
- LevelRQF Level 2
- Total credits40
- Guided learning214 hours
- Units in this qualification72
Awarded by ETC Awards Limited · on the Ofqual register
Start here
See how this course maps onto your role
Ten quick questions, one per Future Fluency, asked against this qualification rather than a generic one.
Check my fluency, free
About 5 minutes · No card · Nothing to commit to
What you’ll learn
What each unit actually teaches you to do
2023 proved to be a hugely successful year, where ETA was honoured as the FAB EPAO of the year, alongside securing Investors in People Gold (Top 10 UK employer)
These are the units ETC Awards Limited registers against this qualification. It is a catalogue, not a syllabus. Which of them you take depends on the combination the qualification requires, and that is set by the awarding body rather than by us. Every unit here is regulated, and every one you earn is yours to keep.
Assembling Structural Sub Assemblies to Produce a Public Service VehicleReal unit · ETC Awards Limited
This unit focuses on interpreting engineering drawings and accurately assembling structural sub-assemblies for public service vehicles. You'll inspect assemblies to ensure they meet specifications and report any defects or discrepancies.
What you'll be able to do
- Assemble structural sub-assemblies accurately and efficiently to produce a public service vehicle, according to specified drawings and instructions.
- Assemble structural sub-assemblies to produce a public service vehicle, understanding the correct techniques and procedures.
Assembling and testing electronic circuitsReal unit · ETC Awards Limited
It teaches you to assemble and test electronic circuits by identifying components, mounting and soldering them accurately, and using testing equipment to verify circuit functionality and performance.
What you'll be able to do
- Assemble electronic circuits following schematic diagrams
- Test electronic circuits to verify functionality and performance
- Know the correct methods for assembling electronic circuits
- Use testing equipment to diagnose faults in electronic circuits
Assembling and testing fluid power systemsReal unit · ETC Awards Limited
You'll develop the ability to assemble and test fluid power systems from engineering drawings and specifications. The unit covers component selection, system assembly, testing methods, and performance verification to ensure system functionality.
What you'll be able to do
- Assemble fluid power systems according to engineering drawings and specifications
- Test assembled fluid power systems to ensure they meet performance requirements
- Know the correct procedures for assembling fluid power systems
- Know the methods used to test fluid power systems
Assembling pattern, model and engineering woodwork componentsReal unit · ETC Awards Limited
It teaches you to assemble pattern, model, and engineering woodwork components according to specifications. You'll interpret drawings, select appropriate tools, and assemble components within specified tolerances, observing health and safety requirements.
What you'll be able to do
- Assemble pattern, model and engineering woodwork components according to specifications and industry standards
- Know the correct procedures for assembling pattern, model and engineering woodwork components, including health and safety requirements
Assembling, wiring and testing electrical panels/components mounted in enclosuresReal unit · ETC Awards Limited
You'll learn to assemble, wire, and test electrical panels and components mounted in enclosures. The unit includes interpreting wiring diagrams, applying appropriate wiring techniques, and verifying functionality and safety through testing.
What you'll be able to do
- Assemble, wire, and test electrical panels and components mounted in enclosures, adhering to relevant industry standards and safety regulations
- Demonstrate knowledge of the principles and practices involved in assembling, wiring, and testing electrical panels and components mounted in enclosures, including component selection, wiring techniques, and testing procedures
Carrying out aircraft detail fitting activitiesReal unit · ETC Awards Limited
You'll prepare, fit, and inspect aircraft detail components according to engineering specifications and established procedures. The unit covers principles of aircraft fitting and the importance of accuracy and documentation in fitting activities.
What you'll be able to do
- Carry out aircraft detail fitting activities, ensuring components are fitted correctly and securely according to engineering specifications.
- Carry out aircraft detail fitting activities, understanding the principles of aircraft fitting and the importance of accuracy.
Carrying out hand forging of engineering materialsReal unit · ETC Awards Limited
You'll learn to carry out hand forging of engineering materials using appropriate tools and techniques. The unit covers shaping processes, heat treatment applications, and the principles underpinning hand forging operations.
What you'll be able to do
- Carry out hand forging of engineering materials, using appropriate tools and techniques
- Know the principles and methods of hand forging engineering materials, including heat treatment and shaping processes
Carrying out heat treatment of engineering materialsReal unit · ETC Awards Limited
You'll carry out heat treatment processes on engineering materials following specified procedures and safety guidelines. The unit covers the principles of heat treatment, different types of processes, and their effects on material properties.
What you'll be able to do
- Carry out heat treatment of engineering materials according to specified procedures and safety guidelines
- Understand the principles of heat treatment of engineering materials, including the different types of heat treatment processes and their effects on material properties
Carrying out maintenance activities on motorsport vehicle electrical equipmentReal unit · ETC Awards Limited
This unit provides learners with skills to carry out maintenance activities on motorsport vehicle electrical equipment. You'll inspect equipment for faults, replace components following manufacturer's instructions, and test repaired equipment for correct operation.
What you'll be able to do
- Carry out maintenance activities on motorsport vehicle electrical equipment according to specified procedures
- Carry out maintenance activities on motorsport vehicle electrical equipment safely and effectively
- Understand the maintenance requirements of motorsport vehicle electrical equipment
- Understand the safety precautions required when working on motorsport vehicle electrical equipment
Conducting business improvement activitiesReal unit · ETC Awards Limited
This unit provides learners with the knowledge and skills to conduct business improvement activities safely and effectively. You'll follow organisational procedures, use personal protective equipment, and understand the purpose and common tools of business improvement.
What you'll be able to do
- Conduct business improvement activities in a safe and effective manner
- Understand how to conduct business improvement activities, including the relevant tools and techniques
Cutting and shaping materials using thermal cutting equipmentReal unit · ETC Awards Limited
This unit covers the selection, setup, and safe operation of thermal cutting equipment to cut and shape materials to required dimensions and tolerances. You'll understand material properties and inspect cut materials to ensure specification compliance.
What you'll be able to do
- Cut and shape materials using thermal cutting equipment, following safety procedures and achieving the required dimensions and tolerances.
- Cut and shape materials using thermal cutting equipment, understanding the properties of different materials and the operation of thermal cutting equipment.
Diagnosing and rectifying faults on motorsport vehicle systems during competitionReal unit · ETC Awards Limited
You'll diagnose and rectify faults on motorsport vehicle systems during competition using appropriate diagnostic techniques and tools. The unit emphasises accurate fault identification, interpretation of diagnostic data, and efficient fault rectification.
What you'll be able to do
- Diagnose faults on motorsport vehicle systems during competition using appropriate techniques
- Rectify faults on motorsport vehicle systems during competition efficiently and effectively
- Describe the methods used to diagnose faults on motorsport vehicle systems during competition
- Explain the procedures for rectifying faults on motorsport vehicle systems during competition
Fettling, finishing and checking cast componentsReal unit · ETC Awards Limited
You'll learn to fettle, finish, and check cast components using appropriate tools and measuring equipment. The unit includes removing excess material, achieving required surface quality, verifying dimensional accuracy, and recognising common defects.
What you'll be able to do
- Fettle, finish and check cast components to meet the required standards
- Demonstrate knowledge of the fettling, finishing and checking processes for cast components
Finishing surfaces by applying coatings or coveringsReal unit · ETC Awards Limited
This unit equips learners with the knowledge and skills to finish surfaces by applying coatings or coverings according to quality standards. You'll understand surface preparation, application procedures, safety guidelines, and how to evaluate and rectify defects in finished surfaces.
What you'll be able to do
- Finish surfaces effectively by applying appropriate coatings or coverings, adhering to safety guidelines and industry standards
- Know the correct procedures for preparing surfaces prior to the application of coatings or coverings
- Know the different types of coatings and coverings available and their suitability for various applications
- Know the health and safety requirements associated with applying coatings and coverings, including the use of personal protective equipment (PPE)
Finishing surfaces by applying treatmentsReal unit · ETC Awards Limited
You'll prepare surfaces and apply finishing treatments to achieve specified quality standards while adhering to safety regulations. The unit includes knowledge of different surface finishing treatments and their correct application methods.
What you'll be able to do
- Finish surfaces effectively by applying appropriate treatments, adhering to specified quality standards and safety regulations
- Demonstrate knowledge of different surface finishing treatments, their application methods, and the factors influencing their selection for various materials and purposes
Fitting Sub Assemblies and Components to Public Service VehiclesReal unit · ETC Awards Limited
This unit covers the fitting of sub-assemblies and components to public service vehicles according to manufacturer's specifications. You'll develop practical skills in preparing vehicles and correctly fitting specified parts, alongside understanding relevant fitting procedures.
What you'll be able to do
- Fit sub-assemblies to public service vehicles according to manufacturer's specifications
- Fit components to public service vehicles according to manufacturer's specifications
- Describe the correct procedures for fitting sub-assemblies to public service vehicles
- Explain the correct procedures for fitting components to public service vehicles
Forming and assembling electrical cable enclosure and support systemsReal unit · ETC Awards Limited
You'll develop the ability to form and assemble electrical cable enclosure and support systems to specified dimensions. The unit includes material preparation, assembly techniques, and adherence to safety procedures.
What you'll be able to do
- Form electrical cable enclosure and support systems to meet specified requirements
- Assemble electrical cable enclosure and support systems according to industry standards
- Know the procedures for forming electrical cable enclosure and support systems safely
- Know the correct techniques for assembling electrical cable enclosure and support systems
Forming and assembling pipework systemsReal unit · ETC Awards Limited
You'll learn to form and assemble pipework systems by cutting, preparing, and bending pipe sections. The unit includes assembling systems using various joining methods and sealing joints to prevent leaks.
What you'll be able to do
- Form pipework systems to meet specified dimensions and tolerances
- Assemble pipework systems using appropriate joining techniques
- Know the procedures for forming pipework systems safely and effectively
- Know the different methods for assembling pipework systems and their applications
General electrical and electronic engineering applicationsReal unit · ETC Awards Limited
You'll carry out general electrical and electronic engineering applications following established procedures and safety regulations. The unit covers principles of circuit design, testing, and fault finding within electrical and electronic systems.
What you'll be able to do
- Carry out general electrical and electronic engineering applications, following established procedures and safety regulations
- Understand the principles and practices of general electrical and electronic engineering applications, including circuit design, testing, and fault finding
General fabrication and welding applicationsReal unit · ETC Awards Limited
You'll learn to carry out general fabrication and welding applications, including cutting, shaping, and joining materials. The unit emphasises safe and effective use of welding equipment and techniques.
What you'll be able to do
- Carry out general fabrication tasks, including cutting, shaping, and joining materials
- Perform welding applications using appropriate techniques and equipment
- Understand the principles of fabrication and welding processes
- Identify different types of welding techniques and their applications
- Recognise the materials suitable for fabrication and welding
- Understand the health and safety requirements when carrying out fabrication and welding activities
General machining, fitting and assembly applicationsReal unit · ETC Awards Limited
You'll carry out general machining, fitting, and assembly operations to specified tolerances and requirements. This unit includes understanding machining types, fitting principles, and interpreting engineering drawings to ensure correct alignment and function.
What you'll be able to do
- Carry out general machining, fitting and assembly applications to specified requirements
- Understand how to carry out general machining, fitting and assembly applications, including the use of appropriate tools and techniques
General maintenance engineering applicationsReal unit · ETC Awards Limited
This unit covers the practical application of general maintenance engineering tasks, including following established procedures and safety protocols. You'll develop skills in carrying out maintenance work, using personal protective equipment, and inspecting completed tasks to ensure quality standards are met.
What you'll be able to do
- Carry out general maintenance engineering applications, following established procedures and safety protocols
- Diagnose common faults in engineering systems and equipment
- Select and use appropriate tools and equipment for general maintenance tasks
- Document maintenance activities accurately and completely
Inspecting a motorsport vehicle during a competitionReal unit · ETC Awards Limited
This unit develops learners' ability to inspect motorsport vehicles during competition according to regulations. You'll identify defects and non-compliance issues, communicate findings clearly, and document inspection processes and results.
What you'll be able to do
- Inspect a motorsport vehicle during a competition, adhering to competition regulations
- Demonstrate knowledge of the inspection procedures and regulations applicable to motorsport vehicles during competition
Installing aircraft mechanical fastenersReal unit · ETC Awards Limited
It teaches you to select, install, and inspect aircraft mechanical fasteners following approved procedures. You'll gain knowledge of different fastener types, installation techniques, and quality control measures to ensure compliance with standards.
What you'll be able to do
- Install aircraft mechanical fasteners correctly and in accordance with approved procedures
- Understand how to install aircraft mechanical fasteners, including fastener types, installation techniques, and quality control measures
Joining Public Service Vehicle Components by Mechanical ProcessesReal unit · ETC Awards Limited
You'll join Public Service Vehicle components using mechanical processes, ensuring accuracy and quality. The unit includes understanding joining methods, techniques, and selection of appropriate tools and materials.
What you'll be able to do
- Join Public Service Vehicle components using appropriate mechanical processes, ensuring accuracy and quality
- Understand the methods and techniques used to join Public Service Vehicle components by mechanical processes, including the selection of appropriate tools and materials
Maintaining and testing process instrumentation and control devicesReal unit · ETC Awards Limited
It teaches you to maintain and test process instrumentation and control devices by following maintenance schedules and workplace procedures. You'll use appropriate testing equipment to verify device operation and document maintenance activities accurately.
What you'll be able to do
- Maintain process instrumentation and control devices according to established schedules and procedures
- Test process instrumentation and control devices to verify correct operation
- Describe the maintenance procedures for process instrumentation and control devices
- Explain the testing methods used to verify the correct operation of process instrumentation and control devices
Maintaining electrical equipment/systemsReal unit · ETC Awards Limited
This unit covers the inspection and maintenance of electrical equipment and systems following established procedures and safety regulations. You'll understand maintenance principles and apply best practices to ensure equipment reliability.
What you'll be able to do
- Maintain electrical equipment and systems effectively, following established procedures, safety regulations, and industry best practices
- Demonstrate knowledge of the principles of electrical equipment and systems maintenance, including fault diagnosis, repair techniques, and preventative maintenance strategies
Maintaining electronic equipment/systemsReal unit · ETC Awards Limited
You'll develop the ability to maintain electronic equipment and systems by following specified procedures. The unit covers using appropriate tools and test equipment to identify and rectify faults, and accurately recording maintenance activities.
What you'll be able to do
- Maintain electronic equipment and systems according to specified procedures
- Demonstrate knowledge of the methods and procedures used to maintain electronic equipment and systems
Maintaining fluid power equipmentReal unit · ETC Awards Limited
You'll gain the skills to maintain fluid power equipment according to manufacturer instructions and safety procedures. The unit covers fault identification, routine maintenance tasks, lubrication, and understanding fluid power system components.
What you'll be able to do
- Maintain fluid power equipment according to manufacturer's instructions and safety procedures
- Identify common faults and malfunctions in fluid power systems
- Perform routine maintenance tasks on fluid power equipment, such as lubrication and filter replacement
- Understand the principles of fluid power systems
- Recognise the components of a fluid power system and their functions
- Understand the health and safety requirements when maintaining fluid power equipment
Maintaining mechanical devices and equipmentReal unit · ETC Awards Limited
It teaches you to maintain mechanical devices and equipment following manufacturer guidelines. You'll apply lubrication techniques, replace worn components, and document maintenance activities accurately.
What you'll be able to do
- Maintain mechanical devices and equipment in accordance with manufacturer guidelines
- Apply appropriate maintenance techniques to mechanical devices and equipment
- Know the safety precautions required when maintaining mechanical devices and equipment
- Know the different types of maintenance procedures for mechanical devices and equipment
Preparing and Manoeuvring Armoured Fighting Vehicles AFVs for Maintenance and TransportationReal unit · ETC Awards Limited
You'll gain the knowledge and skills to prepare and manoeuvre Armoured Fighting Vehicles (AFVs) for maintenance and transportation. This includes identifying maintenance requirements, following safety protocols, and isolating systems prior to maintenance.
What you'll be able to do
- Prepare Armoured Fighting Vehicles (AFVs) for maintenance, ensuring all safety protocols are followed
- Manoeuvre Armoured Fighting Vehicles (AFVs) for transportation, adhering to transportation regulations
- Know the procedures for preparing Armoured Fighting Vehicles (AFVs) for maintenance
- Know the procedures for manoeuvring Armoured Fighting Vehicles (AFVs) for transportation
Preparing and proving CNC fabrication machine tool programsReal unit · ETC Awards Limited
You'll develop the ability to prepare and prove CNC fabrication machine tool programmes by interpreting engineering drawings, selecting tools and parametres, generating programmes, and simulating them to identify errors.
What you'll be able to do
- Prepare CNC fabrication machine tool programs based on engineering drawings
- Prove CNC fabrication machine tool programs to ensure accuracy and efficiency
- Know the principles of CNC programming for fabrication machine tools
- Verify CNC programs to avoid errors and potential damage
Preparing and proving CNC machine tool programsReal unit · ETC Awards Limited
You'll learn to prepare and prove CNC machine tool programs based on engineering drawings and specifications. The unit includes developing, inputting, simulating, and running programs, making adjustments to ensure correct machine tool operation.
What you'll be able to do
- Prepare CNC machine tool programs according to specified requirements
- Prove CNC machine tool programs to ensure correct operation and safety
- Understand the principles of preparing CNC machine tool programs
- Understand the procedures for proving CNC machine tool programs
Preparing and using CNC fabrication machineryReal unit · ETC Awards Limited
You'll develop the skills to prepare and operate CNC fabrication machinery, including loading programmes, setting parametres, and verifying machine calibration. The unit also covers the importance of proper machine preparation for accurate and efficient component fabrication.
What you'll be able to do
- Prepare CNC fabrication machinery for operation, including loading programs and setting parameters
- Use CNC fabrication machinery to produce components according to specified designs
- Interpret CNC programs and identify potential errors
- Maintain CNC fabrication machinery and troubleshoot common problems
Preparing and using CNC machining centresReal unit · ETC Awards Limited
You'll prepare and use CNC machining centres for manufacturing operations following established procedures. The unit covers CNC machining principles, safety precautions, programming basics, and monitoring and adjusting the machining process to meet specifications.
What you'll be able to do
- Prepare and use CNC machining centres for manufacturing operations, following established procedures
- Know the principles of preparing and using CNC machining centres, including safety precautions and programming basics
Preparing and using CNC milling machinesReal unit · ETC Awards Limited
You'll gain knowledge and skills to prepare and use CNC milling machines safely and effectively. The unit covers preparation steps, adherence to manufacturer's instructions and safety guidelines, and operating machines to produce components to required specifications.
What you'll be able to do
- Prepare CNC milling machines in accordance with manufacturer's instructions and safety guidelines
- Use CNC milling machines to produce components to the required specification
- Know the procedures for preparing CNC milling machines for operation
- Know the safety precautions required when using CNC milling machines
Preparing and using CNC turning machinesReal unit · ETC Awards Limited
You'll gain the skills and knowledge to prepare and use CNC turning machines safely and effectively. The unit covers preparation according to manufacturer's instructions and safety guidelines, as well as operating the machines to produce components to specification.
What you'll be able to do
- Prepare CNC turning machines for operation, following manufacturer's instructions and safety guidelines
- Use CNC turning machines to produce components to specified dimensions and tolerances
- Understand the procedures for preparing CNC turning machines for use
- Understand the correct techniques for using CNC turning machines safely and effectively
Preparing and using industrial robotsReal unit · ETC Awards Limited
This unit equips learners to prepare and operate industrial robots safely and effectively according to manufacturer instructions. You'll understand robot components, programming, performance monitoring, and necessary adjustments.
What you'll be able to do
- Prepare industrial robots for operation, following safety procedures and manufacturer's instructions
- Use industrial robots to perform specified tasks, monitoring their performance and making adjustments as necessary
- Understand the principles of operation of industrial robots, including their components, programming, and safety features
Preparing and using lathes for turning operationsReal unit · ETC Awards Limited
This unit equips learners with knowledge and skills to prepare and use lathes for turning operations. You'll follow manufacturer's instructions and workplace procedures to set up lathes safely and perform turning operations to required specifications.
What you'll be able to do
- Prepare lathes for turning operations in accordance with manufacturer's instructions and workplace procedures
- Use lathes to perform turning operations safely and effectively
- Describe the procedures for preparing lathes for turning operations
- Explain the safe and effective use of lathes for turning operations
Preparing and using manual TIG or plasma-arc welding equipmentReal unit · ETC Awards Limited
This unit covers the preparation and use of manual TIG or plasma-arc welding equipment, including the identification of required personal protective equipment and adherence to safety procedures. You'll learn to safely prepare and operate welding equipment effectively.
What you'll be able to do
- Prepare manual TIG or plasma-arc welding equipment for use, following safety procedures
- Use manual TIG or plasma-arc welding equipment to perform welding tasks to the required standard
- Know the correct procedures for preparing manual TIG or plasma-arc welding equipment
- Know the safety requirements for using manual TIG or plasma-arc welding equipment
Preparing and using manual flame brazing and braze welding equipmentReal unit · ETC Awards Limited
This unit covers the preparation and use of manual flame brazing and braze welding equipment. You'll learn to set up equipment, control flames, join metal components, and inspect joints to ensure quality and safety.
What you'll be able to do
- Prepare and use manual flame brazing and braze welding equipment to join metal components, following established safety procedures and techniques
- Demonstrate knowledge of the principles and practices involved in preparing and using manual flame brazing and braze welding equipment, including equipment setup, flame control, and joint preparation
Preparing and using manual metal arc welding equipmentReal unit · ETC Awards Limited
You'll prepare and use manual metal arc welding equipment to produce welds meeting required standards. The unit includes safety procedures, equipment preparation, welding techniques, and maintenance to ensure effective and safe operation.
What you'll be able to do
- Prepare and use manual metal arc welding equipment according to industry standards
- Understand how to prepare and use manual metal arc welding equipment, including safety procedures and equipment maintenance
Preparing and using manual oxy/fuel gas welding equipmentReal unit · ETC Awards Limited
This unit provides learners with the skills to prepare and use manual oxy/fuel gas welding equipment safely and effectively. You'll understand welding principles, equipment components, and produce welds to the required standard.
What you'll be able to do
- Prepare and use manual oxy/fuel gas welding equipment safely and effectively, following established procedures and safety regulations
- Demonstrate knowledge of the principles of oxy/fuel gas welding, the components of the equipment, and the procedures for setting up and using it correctly
Preparing and using milling machinesReal unit · ETC Awards Limited
It teaches you to prepare and operate milling machines safely and effectively according to manufacturer instructions and workplace procedures. You'll perform specified milling operations to required standards.
What you'll be able to do
- Prepare milling machines in accordance with manufacturer's instructions and workplace procedures
- Use milling machines to perform specified operations safely and effectively
- Describe the procedures for preparing milling machines for use
- Explain the safe and effective use of milling machines for specified operations
Preparing and using semi-automatic MIG, MAG and flux cored arc welding equipmentReal unit · ETC Awards Limited
This unit covers the preparation and use of semi-automatic MIG, MAG, and flux cored arc welding equipment. You'll set welding parametres, maintain equipment, and perform welding tasks while adhering to safety procedures and quality standards.
What you'll be able to do
- Prepare semi-automatic MIG, MAG and flux cored arc welding equipment for use
- Use semi-automatic MIG, MAG and flux cored arc welding equipment to perform welding tasks
- Describe the preparation procedures for semi-automatic MIG, MAG and flux cored arc welding equipment
- Explain the operating principles of semi-automatic MIG, MAG and flux cored arc welding equipment
Producing CAD models/drawings using a CAD systemReal unit · ETC Awards Limited
It teaches you to produce CAD models and drawings using a CAD system according to specified design requirements and industry standards. You'll develop skills in CAD functionalities, modelling techniques, and drawing conventions.
What you'll be able to do
- Produce CAD models and drawings using a CAD system, adhering to specified design requirements and industry standards
- Demonstrate knowledge of CAD system functionalities, modelling techniques, and drawing conventions for creating accurate and detailed CAD models and drawings
Producing Composite Mouldings using Resin Film Infusion TechniquesReal unit · ETC Awards Limited
It teaches you to produce composite mouldings using resin film infusion techniques. You'll prepare moulds, apply resin film, infuse and cure the resin, and demould components while understanding relevant materials and infusion processes.
What you'll be able to do
- Produce composite mouldings using resin film infusion techniques to meet specified requirements
- Demonstrate knowledge of the resin film infusion techniques used in the production of composite mouldings
Producing Composite Mouldings using Resin Flow Infusion TechniquesReal unit · ETC Awards Limited
You'll produce composite mouldings using resin flow infusion techniques, including mould preparation, resin mixing, infusion application, and inspection for defects. The unit also covers the principles of resin flow infusion and material properties.
What you'll be able to do
- Produce composite mouldings using resin flow infusion techniques, ensuring correct resin ratios and achieving the required structural integrity.
- Produce composite mouldings using resin flow infusion techniques, understanding the principles of resin flow infusion and the properties of composite materials.
Producing aircraft detail assembliesReal unit · ETC Awards Limited
You'll gain the skills to produce aircraft detail assemblies by interpreting drawings, fabricating components, assembling to specified tolerances, and inspecting completed assemblies to ensure compliance with aviation standards.
What you'll be able to do
- Produce aircraft detail assemblies according to specified drawings, tolerances, and quality standards
- Demonstrate knowledge of the processes involved in producing aircraft detail assemblies, including material selection, fabrication techniques, and inspection procedures
Producing and preparing molten materials for castingReal unit · ETC Awards Limited
This unit covers the production and preparation of molten materials for casting, focusing on achieving the required specifications for temperature and viscosity. You'll develop skills in handling molten materials safely and understanding their properties and associated hazards.
What you'll be able to do
- Produce and prepare molten materials for casting, ensuring quality and safety
- Understand how to produce and prepare molten materials for casting, including material properties and casting processes
Producing and preparing sand moulds and cores for castingReal unit · ETC Awards Limited
You'll learn to produce and prepare sand moulds and cores for casting, meeting specified dimensions and tolerances. The unit includes preparing sand mixtures, achieving required surface finishes, and adhering to safe handling of materials and equipment.
What you'll be able to do
- Produce and prepare sand moulds for casting to meet specified requirements
- Produce and prepare sand cores for casting to meet specified requirements
- Describe the processes involved in producing and preparing sand moulds for casting
- Explain the processes involved in producing and preparing sand cores for casting
Producing cast components by manual meansReal unit · ETC Awards Limited
It teaches you to produce cast components manually, adhering to quality standards and tolerances. You'll prepare moulds, select suitable materials, and apply casting techniques while understanding the importance of quality control and safety.
What you'll be able to do
- Produce cast components by manual means, adhering to specified quality standards and tolerances
- Know the techniques and processes involved in producing cast components by manual means, including material selection and mould preparation
Producing components by rapid prototyping techniquesReal unit · ETC Awards Limited
It teaches you to produce components using rapid prototyping techniques, following established procedures and safety guidelines. You'll understand the principles, operation, and evaluation of rapid prototyping methods.
What you'll be able to do
- Produce components using rapid prototyping techniques, following established procedures and safety guidelines
- Understand the principles and operation of rapid prototyping techniques
- Recognise the different types of rapid prototyping techniques and their applications
- Identify the materials suitable for use in rapid prototyping techniques
- Understand the health and safety requirements when using rapid prototyping equipment
Producing components using hand fitting techniquesReal unit · ETC Awards Limited
It teaches you to produce components using hand fitting techniques to specified tolerances. You'll accurately mark out, shape, and check components using hand tools and measuring instruments, while understanding relevant principles and safety considerations.
What you'll be able to do
- Produce components using hand fitting techniques to meet specified tolerances
- Produce components using hand fitting techniques effectively
- Understand the principles of hand fitting techniques
- Understand the tools and equipment used in hand fitting techniques
Producing composite assembliesReal unit · ETC Awards Limited
This unit provides learners with the skills to produce composite assemblies to specified dimensions and tolerances. You'll understand material preparation, bonding techniques, curing processes, and inspection for defects.
What you'll be able to do
- Produce composite assemblies according to specified designs and quality standards
- Describe the processes involved in producing composite assemblies
- Explain the properties and applications of different composite materials
Producing composite mouldings using pre-preg laminating techniquesReal unit · ETC Awards Limited
This unit provides learners with the skills to produce composite mouldings using pre-preg laminating techniques. You'll prepare moulds, lay up material, apply vacuum bagging, cure mouldings, and inspect for defects.
What you'll be able to do
- Produce composite mouldings using pre-preg laminating techniques.
- Produce composite mouldings using pre-preg laminating techniques.
Producing composite mouldings using wet lay-up techniquesReal unit · ETC Awards Limited
This unit covers the production of composite mouldings using wet lay-up techniques. You'll understand composite material properties and apply correct resin-to-fibre ratios to produce mouldings that meet specified dimensions and tolerances.
What you'll be able to do
- Produce composite mouldings using wet lay-up techniques to meet specified requirements
- Understand the procedures for producing composite mouldings using wet lay-up techniques
- Know the properties and characteristics of different composite materials used in wet lay-up
Producing electrical or electronic engineering drawings using a CAD systemReal unit · ETC Awards Limited
It teaches you to produce electrical or electronic engineering drawings using a CAD system. You'll understand drawing conventions and standards, and create drawings that meet specified requirements for electrical and electronic applications.
What you'll be able to do
- Produce electrical or electronic engineering drawings using a CAD system to meet specified requirements
- Understand the procedures for producing electrical or electronic engineering drawings using a CAD system
- Know the conventions and standards used in electrical and electronic engineering drawings
Producing engineering project plansReal unit · ETC Awards Limited
It teaches you to produce comprehensive engineering project plans by defining objectives, identifying resources, and developing timelines. You'll also understand the importance of project scope, risk management, and resource allocation.
What you'll be able to do
- Produce engineering project plans that include objectives, resources, and timelines
- Develop engineering project plans that meet specified requirements
Producing mechanical assembliesReal unit · ETC Awards Limited
It teaches you to produce mechanical assemblies according to engineering drawings and specifications. You'll gain skills in using appropriate tools and equipment to assemble components and checking assemblies for accuracy and functionality.
What you'll be able to do
- Produce mechanical assemblies according to engineering drawings and specifications
- Use appropriate tools and equipment to assemble mechanical components
- Check the assembled components for accuracy and functionality
- Understand the principles of mechanical assembly
- Recognise different types of mechanical components and their functions
- Understand the health and safety requirements when producing mechanical assemblies
Producing mechanical engineering drawings using a CAD systemReal unit · ETC Awards Limited
You'll produce mechanical engineering drawings using a CAD system, applying geometric tolerances and verifying compliance with industry standards. The unit covers CAD system setup, drawing creation, and output management.
What you'll be able to do
- Produce mechanical engineering drawings using a CAD system to specified standards and tolerances
- Understand the procedures for producing mechanical engineering drawings using a CAD system, including setting up the system, creating drawings, and saving and printing drawings
Producing platework components and assembliesReal unit · ETC Awards Limited
You'll gain the skills to produce platework components and assemblies to specified dimensions and tolerances. The unit includes interpreting engineering drawings, selecting suitable materials and techniques, assembling components, and inspecting finished work for quality and accuracy.
What you'll be able to do
- Produce platework components and assemblies to specified dimensions and tolerances
- Interpret engineering drawings and specifications for platework components and assemblies
- Select appropriate materials and cutting techniques for platework fabrication
- Assemble platework components using appropriate joining methods, such as welding or bolting
Producing sheet metal components and assembliesReal unit · ETC Awards Limited
You'll learn to produce sheet metal components and assemblies from engineering drawings, selecting suitable tools and equipment. The unit emphasises safe working practices and understanding material properties to achieve specified tolerances.
What you'll be able to do
- Produce sheet metal components and assemblies to the required specification
- Demonstrate knowledge of the processes involved in producing sheet metal components and assemblies
Stripping and rebuilding motorsport engines pre-competitionReal unit · ETC Awards Limited
You'll gain skills to strip and rebuild motorsport engines pre-competition by following established procedures. The unit includes identifying and labelling components, recording their condition, and rebuilding engines to meet pre-competition standards.
What you'll be able to do
- Strip motorsport engines in preparation for rebuilding, following established procedures
- Rebuild motorsport engines to meet pre-competition specifications
- Understand the processes involved in stripping motorsport engines
- Understand the processes involved in rebuilding motorsport engines for pre-competition use
Stripping and rebuilding motorsport vehicles pre-competitionReal unit · ETC Awards Limited
This unit equips learners with the skills to strip and rebuild motorsport vehicles pre-competition, following established procedures and safety guidelines. You'll inspect components for wear and damage and reassemble vehicles in accordance with regulations.
What you'll be able to do
- Strip and rebuild motorsport vehicles in preparation for competition, following established procedures and safety guidelines
- Demonstrate knowledge of the processes involved in stripping and rebuilding motorsport vehicles pre-competition, including component identification, inspection, and reassembly techniques
Using and communicating technical informationReal unit · ETC Awards Limited
You'll develop the ability to extract and interpret technical information from manuals, drawings, and specifications. The unit also covers effective verbal and written communication of technical information, ensuring clarity and accuracy in various contexts.
What you'll be able to do
- Use technical information from various sources, such as manuals, drawings, and specifications
- Communicate technical information clearly and accurately to others, both verbally and in writing
- Understand the importance of accurate and reliable technical information
- Recognise different types of technical information and their applications
- Understand the principles of effective communication
- Apply methods for storing and retrieving technical information
Using computer software packages to assist with engineering activitiesReal unit · ETC Awards Limited
You'll develop the ability to use computer software packages to assist with engineering activities, such as creating drawings, performing calculations, and managing data. The unit includes understanding the applications of CAD and other engineering software.
What you'll be able to do
- Use computer software packages to assist with engineering activities effectively
- Describe the applications of computer software packages used in engineering
- Explain the procedures for using computer software packages to assist with engineering activities
Using wood for pattern, modelmaking and other engineering applicationsReal unit · ETC Awards Limited
It teaches you to safely and effectively use wood for pattern making, modelmaking, and other engineering applications. You'll follow established procedures and understand wood properties, selection criteria, and appropriate applications.
What you'll be able to do
- Use wood effectively for pattern making, modelmaking and other engineering applications, following established procedures and safety guidelines
- Demonstrate knowledge of the properties, selection criteria, and appropriate applications of different types of wood used in pattern making, modelmaking and other engineering applications
Wiring and testing electrical equipment and circuitsReal unit · ETC Awards Limited
You'll gain the skills to wire and test electrical equipment and circuits according to wiring diagrams and regulations. The unit includes diagnosing faults, rectifying issues, and documenting wiring and testing processes.
What you'll be able to do
- Wire and test electrical equipment and circuits, ensuring compliance with relevant regulations and safety standards
- Demonstrate knowledge of the principles and practices involved in wiring and testing electrical equipment and circuits, including circuit design, wiring techniques, and testing methods
Wiring and testing programmable controller based systemsReal unit · ETC Awards Limited
This unit covers wiring and testing programmable controller based systems according to wiring diagrams and specifications. You'll connect power supplies and I/O devices, inspect systems for faults, test operation, and understand relevant wiring practices.
What you'll be able to do
- Wire programmable controller based systems according to specified requirements
- Test wired programmable controller based systems to ensure correct operation
- Understand the procedures for wiring programmable controller based systems
- Understand the testing procedures for programmable controller based systems
Working efficiently and effectively in EngineeringReal unit · ETC Awards Limited
You'll develop the ability to work efficiently and effectively in an engineering environment by following workplace procedures, using resources to minimise waste, communicating effectively, maintaining safe work areas, and understanding time management and health and safety principles.
What you'll be able to do
- Work efficiently and effectively in an engineering environment.
- Describe how to work efficiently and effectively in an engineering environment.
Working safely in an engineering environmentReal unit · ETC Awards Limited
You'll develop knowledge and skills to work safely within an engineering environment by understanding relevant health and safety regulations, safe working practices, and correct use of personal protective equipment. The unit emphasises hazard recognition and adherence to established procedures.
What you'll be able to do
- Work safely in an engineering environment, adhering to relevant health and safety regulations.
- Work safely in an engineering environment, following established procedures and risk assessments.
- Work safely in an engineering environment, understanding potential hazards and risks.
- Work safely in an engineering environment, recognising safe working practices and emergency procedures.
The honest bit
You’ve started things before
Most courses were built for a room full of people who aren’t you. A cohort moves on whether or not your week allowed it, and by the third week the thing you’re behind on becomes the reason you stop opening it.
There’s no cohort here, and no timetable to fall behind. Before anything starts, Zavmo asks when you’re sharpest and how long you can realistically sit down for, then builds the sessions around those answers. A bad fortnight changes your pace. It doesn’t put you behind.
And you only pay once you start learning. Searching and planning are free, and you can cancel any time — so the cost of finding out is an afternoon, not a year.
Your passport
Every credit is a stamp you keep
Level 2 credits are regulated. They don’t vanish when a subscription ends or a website closes. They travel to any employer, and Zavmo keeps the map of what you’ve earned and what’s next.
Assembling Structural Sub Assemblies to Produce a Public Service VehicleAssembling and testing electronic circuitsAssembling and testing fluid power systemsAssembling pattern, model and engineering woodwork componentsAssembling, wiring and testing electrical panels/components mounted in enclosuresCarrying out aircraft detail fitting activitiesCarrying out hand forging of engineering materialsCarrying out heat treatment of engineering materials
Each stamp is a real unit registered against this qualification.
Who’d teach you this
The Evidence Evaluator
Assessor
Helps you show what you can actually do, gathering the evidence that proves it as you learn.
Meet all twelve tutorsWhere this connects
Where these credits take you
A qualification is never a dead end here. See the jobs its credits open, the national occupational standards its units map to, and the future skills they quietly build.
ETCAL Level 2 Diploma in Performing Engineering Operations (Northern Ireland)
- Assembling and testing electronic circuits
- Carrying out maintenance activities on motorsport vehicle electrical equipment
- Fettling, finishing and checking cast components Legacy
- Finishing components by applying transfers, decals and livery
- Finishing surfaces by applying coatings or coverings Legacy
- Finishing surfaces by applying treatments Legacy
- Fitting Sub Assemblies and Components to Public Service Vehicles Legacy
- Fitting ancillary units to commercial and passenger carrying vehicles
Where this can lead
Maintenance Technician
Your career here is what you make it. We'll give you the tools, the training, and the opportunities; you bring the drive and the willingness to learn. The sky's the limit if you're prepared to put in the work.
See the whole journey →Opens the roleMaintenance TechnicianOne of the jobs this qualification is a route intoSee the role →Opens the roleAssociate Prototype AssistantOne of the jobs this qualification is a route intoSee the role →Opens the roleDirector of Rapid PrototypingOne of the jobs this qualification is a route intoSee the role →Future FluencyAll ten future skillsSee how every unit is contextualised by the tenExplore →
Skills it covers
What the job actually needs. These are the standards the units are built against, in the words employers and awarding bodies already use for the work itself.
Assembling and testing electronic circuitsCarrying out maintenance activities on motorsport vehicle electrical equipmentFettling, finishing and checking cast components LegacyFinishing components by applying transfers, decals and liveryFinishing surfaces by applying coatings or coverings LegacyFinishing surfaces by applying treatments LegacyFitting Sub Assemblies and Components to Public Service Vehicles LegacyFitting ancillary units to commercial and passenger carrying vehiclesForming and Assembling Electrical Cable Enclosure and Support Systems LegacyForming and Assembling Pipework SystemsForming and Assembling Pipework Systems LegacyForming and assembling electrical cable enclosure and support systemsGeneral Fabrication and Welding Applications LegacyMaintaining mechanical devices and equipment LegacyProducing Cast Components by Manual Means LegacyProducing and preparing sand moulds and cores for casting LegacyProducing ceramic moulds or coresProducing components by rapid prototyping techniques Legacy+5 more
How you’ll actually learn this
One-to-one, on your own real work
A qualification is usually something done to you: sit the class, sit the exam, hope it sticks. Here it’s the opposite. You learn it one-to-one with a companion, on your own real work, and you keep going until you can use it, not just recall it.
One-to-one, on your real workNo lectures, no past-papers. Every unit is practised on the actual tasks your job throws at you, a tutor beside you, not a video in front of you.
Taught to the top, not the testMost courses stop at remembering. Your companion keeps climbing: analysing, judging, creating. That’s the part a machine can’t do for you.
Credits you keep, a map that continuesEvery unit is regulated and yours for good. The day you finish, Zavmo already knows the next role your new credits open.
Applied to your work in any of these jobs
Which job do you mean?
This unit focuses on interpreting engineering drawings and accurately assembling structural sub-assemblies for public service vehicles. Learners will inspect assemblies to ensure they meet specifications and report any defects or discrepancies.
How the thinking builds
- Remember
- Understand
- Apply
- Analyse
- Evaluate
- Create
Built for ETCAL Level 2 Diploma in Performing Engineering Operations (Northern Ireland)
72 units in this credential, in the order it lists them, awarded by ETC Awards Limited.
- Assembling Structural Sub Assemblies to Produce a Public Service Vehicle
- Assembling and testing electronic circuits
- Assembling and testing fluid power systems
- Assembling pattern, model and engineering woodwork components
- Assembling, wiring and testing electrical panels/components mounted in enclosures
- Carrying out aircraft detail fitting activities
and 66 more in the full unit list below.
One to one, not one to many
No two people run this the same way
A course is written once and handed to everyone. This is assembled around you, and keeps changing as it learns you. Five things it reads, and what each one changes.
- Your actual work Every unit is taught against a live piece of your own work, not a worked example from a textbook.
- What you already know The first conversation finds your starting point, so you skip what you can already do and spend the time on what you cannot.
- The conditions you learn under Not a learning-styles quiz. The evidence does not support those. The dimensions the research does back, read once and used to shape the plan.
- How far you got last time It picks up mid-thought. The tutor knows what you said, what you struggled with, and what it asked you to try.
- Which tutor suits the moment Twelve of them, each for a different kind of thinking. The one who walks you through a first idea is not the one who stress-tests it.
See how you learn, free. Eight questions, no sign-up. A directional taster; the diagnostic inside Zavmo goes deeper and keeps adapting.
Why it sticks
Most courses stop at remembering
There’s a well-known ladder of how deeply you learn something, called Bloom’s Taxonomy. Most courses get you up the first two rungs: you remember some facts, you pass a test, you forget it. Real skill lives at the top. Judging, deciding, creating. And this isn’t a generic ladder: every rung has a named Zavmo tutor who walks you up it.
- 6CreateThe Creative Catalyst
- 5EvaluateThe Evidence Evaluator
- 4AnalyseThe Analyst
- 3ApplyThe Coach
- 2UnderstandThe Connector
- 1RememberThe Builder
Where most courses leave you Where Zavmo takes you
Why this matters: AI can already remember and understand for you. What it can’t do is
take your real problem and judge the right call. So the only learning worth paying
for is the learning that takes you to the top. That’s exactly what a tutor doing it with
you, on your real work, is for.
The value
Why the companion is worth £70 a month
You’re not paying for the units. They’re regulated, and the same wherever you earn them. You’re paying for the one thing that decides whether you actually get there: a companion that makes them stick, on your real work.
That is one-to-one on this qualification, every day, on the work you already do, for £70 a month. Your first module is free, so you can see the teaching before you pay for any of it. Billed monthly, cancel any time and billing stops.
Earned on your own work, taught to the top.
Everything you just read, learned one-to-one on the job you already do. Your first module is free, so you can see the teaching before you pay for any of it.
Build my plan, freeNo card. See how this qualification maps onto your role and meet the tutors who’d teach it, free. The learning begins when you subscribe. It’s £70 a month, billed monthly. Cancel any time and billing stops.