GQA Qualifications Limited · RQF Level 2
GQA PAA\VQ-SET Level 2 NVQ Diploma in Performing Engineering Operations
You don’t just earn this. You learn to use it, one-to-one, on your own real work.
- LevelRQF Level 2
- Total credits40
- Guided learning214 hours
- Units in this qualification73
Awarded by GQA Qualifications Limited · on the Ofqual register
Start here
See how this course maps onto your role
Ten quick questions, one per Future Fluency, asked against this qualification rather than a generic one.
Check my fluency, free
About 5 minutes · No card · Nothing to commit to
What you’ll learn
What each unit actually teaches you to do
The NVQ Diploma in Performing Engineering Operations is an occupational qualification. It allows learners to develop skills in assembling woodwork and producing cast components. It also covers wiring and testing electrical panels and programmable controller based systems.
These are the units GQA Qualifications Limited registers against this qualification. It is a catalogue, not a syllabus. Which of them you take depends on the combination the qualification requires, and that is set by the awarding body rather than by us. Every unit here is regulated, and every one you earn is yours to keep.
Assembling Structural Sub Assemblies to Produce a Public Service VehicleReal unit · GQA Qualifications Limited
You'll develop the skills to assemble structural sub-assemblies for public service vehicles according to specified drawings and instructions. The unit includes ensuring quality standards are met and understanding the function and importance of different structural components.
What you'll be able to do
- Assemble structural sub-assemblies to produce a public service vehicle, according to specified drawings and instructions.
- Demonstrate knowledge of how to assemble structural sub-assemblies to produce a public service vehicle, including the correct use of tools and equipment.
Assembling and testing electronic circuitsReal unit · GQA Qualifications Limited
You'll learn to assemble and test electronic circuits based on circuit diagrams and component specifications. The unit covers using test equipment to verify functionality, diagnosing faults, rectifying issues, and understanding electronic components and safety practices.
What you'll be able to do
- Assemble and test electronic circuits according to given instructions and specifications
- Demonstrate knowledge of the principles and practices of assembling and testing electronic circuits
Assembling and testing fluid power systemsReal unit · GQA Qualifications Limited
It teaches you to assemble and test fluid power systems according to engineering specifications. You'll connect components using appropriate fittings, test for leaks and pressure integrity, and adjust system settings to achieve desired performance.
What you'll be able to do
- Assemble and test fluid power systems according to engineering drawings and specifications, ensuring proper functionality and leak-free operation
- Demonstrate knowledge of the procedures involved in assembling and testing fluid power systems, including component identification, connection methods, and pressure testing techniques
Assembling pattern, model and engineering woodwork componentsReal unit · GQA Qualifications Limited
It teaches you to accurately assemble pattern, model, and engineering woodwork components by following instructions and drawings. You'll also learn how to check assembled components for accuracy and quality, using appropriate tools and techniques.
What you'll be able to do
- Assemble pattern woodwork components accurately, following instructions and drawings.
- Assemble model woodwork components accurately, following instructions and drawings.
- Assemble engineering woodwork components accurately, following instructions and drawings.
- Prepare components for assembly, including cleaning, sanding, and applying adhesives.
- Use appropriate tools and equipment for assembling woodwork components safely and effectively.
- Check the assembled components for accuracy and quality, and make any necessary adjustments.
Assembling, wiring and testing electrical panels/components mounted in enclosuresReal unit · GQA Qualifications Limited
You'll gain the ability to assemble, wire, and test electrical panels and components mounted in enclosures safely and effectively. The unit includes knowledge of different panel types, wiring methods, and testing procedures to ensure compliance with performance requirements.
What you'll be able to do
- Assemble, wire and test electrical panels and components mounted in enclosures safely and effectively
- Demonstrate knowledge of the assembly, wiring and testing procedures for electrical panels and components mounted in enclosures
Carrying out aircraft detail fitting activitiesReal unit · GQA Qualifications Limited
You'll carry out aircraft detail fitting activities, including preparing work areas, selecting tools, fitting components according to drawings, and inspecting completed work to ensure compliance with specifications.
What you'll be able to do
- Carry out aircraft detail fitting activities to the required specifications
- Describe the procedures for carrying out aircraft detail fitting activities
- Explain the importance of adhering to safety regulations when carrying out aircraft detail fitting activities
Carrying out engineering activities efficiently and effectivelyReal unit · GQA Qualifications Limited
This unit develops learners' ability to work efficiently and effectively in engineering environments. Skills include time management, workspace organisation, resource utilisation, and clear communication with colleagues.
What you'll be able to do
- Apply efficient and effective working practices in an engineering environment.
- Demonstrate effective communication and teamwork skills in engineering activities.
- Understand the principles of working efficiently and effectively in engineering.
- Understand the importance of communication and teamwork in engineering.
Carrying out hand forging of engineering materialsReal unit · GQA Qualifications Limited
This unit provides learners with practical skills in hand forging engineering materials. You'll select suitable forging techniques, apply them to shape materials to desired dimensions, and maintain material quality throughout the forging process.
What you'll be able to do
- Carry out hand forging of engineering materials using appropriate techniques
- Select and prepare engineering materials for hand forging
- Use hand forging tools and equipment safely and effectively
- Shape and form engineering materials using hand forging techniques
Carrying out heat treatment of engineering materialsReal unit · GQA Qualifications Limited
It teaches you to carry out heat treatment of engineering materials by preparing materials, applying appropriate methods, monitoring processes, and documenting results. You'll also understand the principles and purposes of heat treatment in material engineering.
What you'll be able to do
- Carry out heat treatment of engineering materials using appropriate methods and equipment.
- Carry out heat treatment of engineering materials, including understanding the principles of heat treatment and the properties of different materials.
Carrying out maintenance activities on motorsport vehicle electrical equipmentReal unit · GQA Qualifications Limited
This unit develops learners' ability to carry out maintenance on motorsport vehicle electrical equipment. You'll perform maintenance tasks, diagnose faults using testing equipment, replace faulty components, and ensure correct electrical connections.
What you'll be able to do
- Carry out maintenance activities on motorsport vehicle electrical equipment, adhering to manufacturer's specifications and safety regulations
- Demonstrate knowledge of the procedures involved in carrying out maintenance activities on motorsport vehicle electrical equipment, including fault diagnosis, component replacement, and system testing
Conducting business improvement activitiesReal unit · GQA Qualifications Limited
It teaches you to conduct business improvement activities using recognised methodologies. You'll plan, gather and analyse data, implement improvements, and monitor progress to evaluate effectiveness.
What you'll be able to do
- Conduct business improvement activities in a structured and organised manner.
- Implement business improvement activities to achieve specific objectives.
- Understand the principles of conducting business improvement activities.
- Understand the methods for implementing business improvement activities.
Cutting and shaping materials using thermal cutting equipmentReal unit · GQA Qualifications Limited
This unit provides learners with the skills to cut and shape materials using thermal cutting equipment safely and accurately. You'll adhere to safety procedures, achieve required dimensions, and understand the principles of various thermal cutting processes.
What you'll be able to do
- Cut and shape materials using thermal cutting equipment, adhering to safety procedures and achieving required dimensions.
- Demonstrate knowledge of how to cut and shape materials using thermal cutting equipment, including the selection of appropriate equipment and settings.
Diagnosing and rectifying faults on motorsport vehicle systems during competitionReal unit · GQA Qualifications Limited
It teaches you to diagnose and rectify faults on motorsport vehicle systems during competition. You'll use diagnostic tools and techniques to identify faults, document the process, and carry out necessary repairs to maintain vehicle performance and safety.
What you'll be able to do
- Diagnose faults on motorsport vehicle systems during competition, using appropriate diagnostic tools and techniques
- Rectify faults on motorsport vehicle systems during competition, ensuring the vehicle meets performance and safety requirements
- Demonstrate knowledge of fault diagnosis procedures for motorsport vehicle systems
- Demonstrate knowledge of the rectification techniques for motorsport vehicle systems
Fettling, finishing and checking cast componentsReal unit · GQA Qualifications Limited
You'll learn to fettle, finish, and check cast components according to workplace procedures. The unit includes removing excess material, achieving required surface quality, and inspecting components for dimensional accuracy and defects using suitable measuring equipment.
What you'll be able to do
- Fettle, finish and check cast components in accordance with workplace procedures
- Demonstrate knowledge of the techniques used to fettle, finish and check cast components
Finishing surfaces by applying coatings or coveringsReal unit · GQA Qualifications Limited
You'll finish surfaces by preparing and applying coatings or coverings evenly and consistently. The unit includes inspecting finished surfaces, rectifying defects, and understanding different types of coatings and coverings used.
What you'll be able to do
- Finish surfaces by applying coatings or coverings to meet required specifications.
- Understand the methods and techniques used to finish surfaces by applying coatings or coverings.
Finishing surfaces by applying treatmentsReal unit · GQA Qualifications Limited
You'll develop the ability to finish surfaces by applying treatments following specified procedures. The unit covers surface cleaning methods, identification of contaminants, preparation techniques, and the application of treatments to achieve quality surface finishes.
What you'll be able to do
- Prepare surfaces for the application of treatments, ensuring they are clean and free from contaminants
- Apply surface treatments according to specified procedures and quality standards
- Demonstrate knowledge of different surface treatments and their applications
- Demonstrate knowledge of the preparation and application techniques for surface treatments
Fitting Sub Assemblies and Components to Public Service VehiclesReal unit · GQA Qualifications Limited
You'll develop the ability to fit sub-assemblies and components to public service vehicles following manufacturer specifications. The unit covers vehicle preparation, component fitting, inspection for correct operation, and accurate documentation of the fitting process.
What you'll be able to do
- Fit sub-assemblies and components to public service vehicles according to manufacturer's specifications and industry standards.
- Fit sub-assemblies and components to public service vehicles, including understanding the relevant tools, techniques, and safety procedures.
Forming and assembling electrical cable enclosure and support systemsReal unit · GQA Qualifications Limited
You'll learn to form and assemble electrical cable enclosure and support systems by interpreting specifications and applying appropriate forming techniques. The unit includes inspecting formed components for defects and ensuring compliance with industry standards.
What you'll be able to do
- Form electrical cable enclosure and support systems to meet specified requirements
- Assemble electrical cable enclosure and support systems according to industry standards
- Know the procedures for forming electrical cable enclosure and support systems
- Know the techniques for assembling electrical cable enclosure and support systems
Forming and assembling pipework systemsReal unit · GQA Qualifications Limited
This unit equips learners with the skills to form and assemble pipework systems to specified dimensions and angles. You'll use appropriate tools and joining techniques to ensure pipework is free from defects and joints are leak-proof and secure.
What you'll be able to do
- Form pipework systems to meet specified requirements
- Assemble pipework systems to meet specified requirements
- Know the techniques used to form pipework systems
- Know the techniques used to assemble pipework systems
General electrical and electronic engineering applicationsReal unit · GQA Qualifications Limited
You'll carry out general electrical and electronic engineering tasks following safe working practices. The unit includes performing wiring, connections, and testing of circuits and components to industry standards.
What you'll be able to do
- Carry out general electrical engineering applications in accordance with industry standards
- Carry out general electronic engineering applications in accordance with industry standards
- Describe the procedures for carrying out general electrical and electronic engineering applications
- Explain the importance of adhering to safety regulations when carrying out general electrical and electronic engineering applications
General fabrication and welding applicationsReal unit · GQA Qualifications Limited
It teaches you to carry out general fabrication and welding applications safely and effectively. You'll follow established procedures, adhere to safety guidelines, and produce fabricated and welded components to required standards, understanding material properties involved.
What you'll be able to do
- Carry out general fabrication and welding applications, following established procedures and safety guidelines.
- Demonstrate knowledge of how to carry out general fabrication and welding applications, including the selection of appropriate materials and techniques.
General machining, fitting and assembly applicationsReal unit · GQA Qualifications Limited
This unit provides learners with the skills to carry out general machining, fitting, and assembly applications in line with specified procedures and safety guidelines. You'll produce components to required tolerances and finishes, demonstrating safe working practices throughout.
What you'll be able to do
- Carry out general machining applications in accordance with specified procedures and safety guidelines
- Carry out general fitting applications in accordance with specified procedures and safety guidelines
- Carry out general assembly applications in accordance with specified procedures and safety guidelines
- Know the procedures for carrying out general machining applications
- Know the procedures for carrying out general fitting applications
- Know the procedures for carrying out general assembly applications
General maintenance engineering applicationsReal unit · GQA Qualifications Limited
You'll carry out general maintenance engineering tasks following work orders and safety protocols. The unit includes documenting maintenance activities and understanding the principles of operation of common engineering systems.
What you'll be able to do
- Carry out general maintenance engineering applications competently, following established procedures and safety protocols
- Demonstrate knowledge of the principles and practices involved in general maintenance engineering applications
Inspecting a motorsport vehicle during a competitionReal unit · GQA Qualifications Limited
It teaches you to inspect a motorsport vehicle during competition by following established procedures and using appropriate tools. You'll identify defects or issues, record findings accurately, and understand the categorisation of inspection outcomes.
What you'll be able to do
- Inspect a motorsport vehicle during a competition, following established procedures
- Identify any defects or issues during the inspection of a motorsport vehicle
- Know the procedures for inspecting a motorsport vehicle during a competition
- Identify defects or issues during the inspection of a motorsport vehicle
Installing aircraft mechanical fastenersReal unit · GQA Qualifications Limited
This unit provides learners with the skills to select, install, and inspect aircraft mechanical fasteners according to specified procedures. You'll understand various fastener types, correct installation techniques, and safety considerations to ensure secure and compliant fastening.
What you'll be able to do
- Install aircraft mechanical fasteners correctly and safely.
- Understand the procedures and safety precautions for installing aircraft mechanical fasteners.
Joining Public Service Vehicle Components by Mechanical ProcessesReal unit · GQA Qualifications Limited
You'll develop the ability to join Public Service Vehicle components using appropriate mechanical processes while adhering to health and safety procedures. The unit emphasises the use of correct tools and ensuring joints meet specified strength and quality standards.
What you'll be able to do
- Join Public Service Vehicle components using appropriate mechanical processes
- Apply relevant health and safety procedures when joining Public Service Vehicle components
- Know the different mechanical processes used to join Public Service Vehicle components
- Know the health and safety requirements when joining Public Service Vehicle components
Maintaining and testing process instrumentation and control devicesReal unit · GQA Qualifications Limited
You'll maintain and test process instrumentation and control devices following established procedures. The unit includes correct use of tools, performing tests to identify faults, and accurate recording of maintenance activities.
What you'll be able to do
- Maintain process instrumentation and control devices in accordance with established procedures.
- Test process instrumentation and control devices to ensure correct functionality.
- Understand the procedures for maintaining process instrumentation and control devices.
- Understand the methods used to test process instrumentation and control devices.
Maintaining electrical equipment/systemsReal unit · GQA Qualifications Limited
You'll gain the skills and knowledge to maintain electrical equipment and systems safely and effectively. The unit includes inspecting for faults, performing maintenance in compliance with safety regulations, testing equipment post-maintenance, and documenting all maintenance activities.
What you'll be able to do
- Maintain electrical equipment and systems in accordance with safety regulations and industry best practices.
- Maintain electrical equipment and systems, including understanding electrical principles, testing procedures, and safety precautions.
Maintaining electronic equipment/systemsReal unit · GQA Qualifications Limited
This unit equips learners with skills to maintain electronic equipment and systems safely and effectively. You'll follow established procedures, evaluate maintenance effectiveness, and understand the principles of electronic operation.
What you'll be able to do
- Maintain electronic equipment and systems effectively, following established procedures and safety guidelines
- Demonstrate knowledge of the principles and practices involved in maintaining electronic equipment and systems
Maintaining fluid power equipmentReal unit · GQA Qualifications Limited
You'll gain knowledge and skills to maintain fluid power equipment effectively. The unit covers maintenance procedures following manufacturer instructions, application of safety regulations, and identification of different fluid power equipment types with their specific maintenance needs.
What you'll be able to do
- Maintain fluid power equipment in accordance with manufacturer's instructions and safety regulations
- Describe the procedures for maintaining fluid power equipment
- Explain the importance of regular maintenance for fluid power equipment
Maintaining mechanical devices and equipmentReal unit · GQA Qualifications Limited
You'll gain knowledge and skills to maintain mechanical devices and equipment effectively, applying correct maintenance procedures and safety regulations. The unit includes identifying required tools, performing maintenance tasks, and accurately recording maintenance activities.
What you'll be able to do
- Maintain mechanical devices and equipment in accordance with specified procedures and safety regulations.
- Maintain mechanical devices and equipment, including understanding the relevant tools, techniques, and safety precautions.
Preparing and Manoeuvring Armoured Fighting Vehicles AFVs for Maintenance and TransportationReal unit · GQA Qualifications Limited
This unit provides learners with the ability to prepare and manoeuvre Armoured Fighting Vehicles (AFVs) for maintenance and transportation. You'll perform pre-manoeuvring checks, apply safe manoeuvring techniques, and prepare AFVs in accordance with relevant regulations and procedures.
What you'll be able to do
- Prepare and manoeuvre Armoured Fighting Vehicles (AFVs) for maintenance and transportation safely and effectively
- Demonstrate knowledge of the procedures for preparing and manoeuvring Armoured Fighting Vehicles (AFVs) for maintenance and transportation
Preparing and proving CNC fabrication machine tool programsReal unit · GQA Qualifications Limited
This unit covers the preparation and proving of CNC fabrication machine tool programs. You'll learn to interpret engineering drawings, prepare CNC programs based on specifications, and select appropriate cutting tools and parametres to ensure accurate and efficient machining.
What you'll be able to do
- Prepare CNC fabrication machine tool programs based on engineering drawings and specifications
- Prove CNC fabrication machine tool programs to ensure accuracy and efficiency
- Demonstrate knowledge of CNC programming principles and techniques
- Demonstrate knowledge of the proving process for CNC fabrication machine tool programs
Preparing and proving CNC machine tool programsReal unit · GQA Qualifications Limited
This unit covers the preparation and proving of CNC machine tool programs, including programme creation, simulation to detect errors, proving on the machine, and adjustments to optimise performance. You'll gain practical skills and knowledge to ensure accurate and efficient CNC machining operations.
What you'll be able to do
- Prepare and prove CNC machine tool programs to ensure correct operation.
- Understand the principles and procedures for preparing and proving CNC machine tool programs.
Preparing and using CNC fabrication machineryReal unit · GQA Qualifications Limited
You'll develop the ability to prepare and use CNC fabrication machinery safely and effectively. The unit covers inspection, calibration, pre-use checks, and operation of machinery to produce components to specified dimensions.
What you'll be able to do
- Prepare CNC fabrication machinery for use in accordance with manufacturer's instructions and safety guidelines
- Use CNC fabrication machinery to produce components to specified requirements
- Demonstrate knowledge of the principles and procedures for preparing and using CNC fabrication machinery
Preparing and using CNC machining centresReal unit · GQA Qualifications Limited
This unit equips learners with the skills and knowledge to prepare and operate CNC machining centres. You'll interpret technical drawings, set up tooling and fixtures, establish datum points and offsets, and monitor machining processes to produce components to specification.
What you'll be able to do
- Prepare CNC machining centres for specific tasks, ensuring correct setup and tooling
- Use CNC machining centres to produce components according to technical drawings and specifications
- Know the procedures for preparing CNC machining centres
- Know the techniques for using CNC machining centres
Preparing and using CNC milling machinesReal unit · GQA Qualifications Limited
This unit equips learners to prepare and operate CNC milling machines safely and effectively. You'll follow established procedures for machine setup, adhere to safety guidelines, and produce components to specified dimensions while managing machine functionality.
What you'll be able to do
- Prepare CNC milling machines in accordance with established procedures and safety guidelines
- Use CNC milling machines to produce components to specified requirements
- Prepare CNC milling machines for operation, including setting tools and workholding devices
- Use CNC milling machines safely and effectively to produce components
Preparing and using CNC turning machinesReal unit · GQA Qualifications Limited
You'll prepare and operate CNC turning machines to produce components to specified dimensions and tolerances. The unit includes inspecting, calibrating, and performing pre-use checks to ensure safe and accurate machine operation.
What you'll be able to do
- Prepare CNC turning machines for use in accordance with manufacturer's instructions and safety guidelines
- Use CNC turning machines to produce components to specified requirements
- Demonstrate knowledge of the principles and procedures for preparing and using CNC turning machines
Preparing and using grinding machinesReal unit · GQA Qualifications Limited
This unit equips learners with the skills to prepare and use grinding machines safely and effectively. You'll follow manufacturer instructions, achieve specified surface finishes and tolerances, and understand safety guidelines and machine preparation principles.
What you'll be able to do
- Prepare grinding machines in accordance with manufacturer's instructions and safety guidelines
- Use grinding machines to achieve specified surface finishes and tolerances
- Demonstrate knowledge of the preparation procedures for grinding machines
- Demonstrate knowledge of the correct operating procedures for grinding machines
Preparing and using industrial robotsReal unit · GQA Qualifications Limited
This unit covers the preparation and use of industrial robots for tasks such as welding, painting, or assembly. You'll set up robots, operate them safely, and understand the principles of robot operation and programming.
What you'll be able to do
- Prepare and use industrial robots effectively for designated tasks, adhering to safety guidelines and operational procedures
- Demonstrate knowledge of the principles of industrial robot operation, programming, and maintenance
Preparing and using lathes for turning operationsReal unit · GQA Qualifications Limited
You'll develop the skills to prepare and use lathes for turning operations safely and accurately. The unit includes setting up lathes with appropriate tooling, performing turning to specified dimensions and tolerances, and applying correct cutting speeds.
What you'll be able to do
- Prepare lathes for turning operations, ensuring correct setup and tooling
- Use lathes to perform turning operations, producing components to specified dimensions and tolerances
- Describe the procedures for preparing and using lathes for turning operations
- Explain the importance of following safety procedures when operating lathes
Preparing and using manual TIG or plasma-arc welding equipmentReal unit · GQA Qualifications Limited
You'll learn to prepare and use manual TIG or plasma-arc welding equipment. The unit covers equipment setup, parametre selection, welding techniques, and inspection of welds for quality and defects.
What you'll be able to do
- Prepare and use manual TIG or plasma-arc welding equipment to create quality welds, following established welding techniques and safety protocols
- Demonstrate knowledge of the procedures involved in preparing and using manual TIG or plasma-arc welding equipment, including equipment setup, parameter selection, and weld inspection
Preparing and using manual flame brazing and braze welding equipmentReal unit · GQA Qualifications Limited
This unit covers the preparation and use of manual flame brazing and braze welding equipment. You'll inspect and set up equipment, check gas supplies, select materials, and apply heat effectively while adhering to safety procedures.
What you'll be able to do
- Prepare manual flame brazing equipment for use in accordance with safety guidelines
- Prepare manual braze welding equipment for use in accordance with safety guidelines
- Use manual flame brazing equipment to complete brazing tasks
- Use manual braze welding equipment to complete welding tasks
- Describe the procedures for preparing and using manual flame brazing and braze welding equipment
- Explain the importance of adhering to safety regulations when preparing and using manual flame brazing and braze welding equipment
Preparing and using manual metal arc welding equipmentReal unit · GQA Qualifications Limited
You'll prepare and use manual metal arc welding equipment to create welds in various positions while following safety procedures. The unit covers the principles of manual metal arc welding, equipment functions, and the importance of personal protective equipment.
What you'll be able to do
- Prepare and use manual metal arc welding equipment in a safe and competent manner
- Demonstrate knowledge of the preparation and use of manual metal arc welding equipment
Preparing and using manual oxy/fuel gas welding equipmentReal unit · GQA Qualifications Limited
This unit develops learners' ability to safely prepare and use manual oxy/fuel gas welding equipment. You'll inspect equipment, set up according to guidelines, adjust gas pressures, and perform welding tasks to meet specified standards.
What you'll be able to do
- Prepare manual oxy/fuel gas welding equipment for use in accordance with safety regulations and manufacturer's guidelines
- Use manual oxy/fuel gas welding equipment to perform welding tasks to a specified standard
- Demonstrate knowledge of the principles and procedures for preparing and using manual oxy/fuel gas welding equipment
Preparing and using milling machinesReal unit · GQA Qualifications Limited
It teaches you to prepare and operate milling machines safely to produce components to required dimensions and tolerances. You'll understand machine setup, tool selection, and safe operating procedures.
What you'll be able to do
- Prepare and use milling machines safely and effectively to produce components to the required specifications
- Demonstrate knowledge of the principles of milling, machine setup, and the selection of appropriate cutting tools and parameters
Preparing and using semi-automatic MIG, MAG and flux cored arc welding equipmentReal unit · GQA Qualifications Limited
This unit covers preparing and using semi-automatic MIG, MAG, and flux cored arc welding equipment. You'll prepare equipment, produce welds to required standards, maintain equipment, and understand welding principles, equipment components, and associated safety hazards.
What you'll be able to do
- Prepare and use semi-automatic MIG, MAG and flux cored arc welding equipment in a safe and effective manner
- Demonstrate knowledge of the preparation and use of semi-automatic MIG, MAG and flux cored arc welding equipment
Producing CAD models/drawings using a CAD systemReal unit · GQA Qualifications Limited
You'll produce CAD models and drawings using a CAD system to meet specified requirements and industry standards. The unit covers the use of software tools and techniques to generate accurate, detailed designs and an understanding of CAD system functions.
What you'll be able to do
- Produce CAD models and drawings using a CAD system, meeting specified requirements and industry standards.
- Demonstrate knowledge of how to produce CAD models and drawings using a CAD system, including the use of relevant software tools and techniques.
Producing Composite Mouldings using Resin Film Infusion TechniquesReal unit · GQA Qualifications Limited
This unit equips learners to produce composite mouldings using resin film infusion techniques. You'll prepare materials and equipment, apply infusion methods, and inspect finished mouldings for defects and compliance with specifications.
What you'll be able to do
- Produce composite mouldings using resin film infusion techniques to meet specified requirements
- Demonstrate knowledge of the processes involved in producing composite mouldings using resin film infusion techniques
Producing Composite Mouldings using Resin Flow Infusion TechniquesReal unit · GQA Qualifications Limited
This unit covers the preparation and use of resin flow infusion techniques to produce composite mouldings. You'll develop skills in preparing materials and equipment, applying infusion methods, and inspecting finished mouldings for defects and compliance with specifications.
What you'll be able to do
- Produce composite mouldings using resin flow infusion techniques to meet specified requirements
- Demonstrate knowledge of the processes involved in producing composite mouldings using resin flow infusion techniques
Producing aircraft detail assembliesReal unit · GQA Qualifications Limited
You'll produce aircraft detail assemblies following specified drawings and instructions. The unit includes adherence to industry standards and safety regulations, as well as inspection of completed assemblies for quality assurance.
What you'll be able to do
- Produce aircraft detail assemblies to the required specifications, adhering to industry standards and safety regulations
- Demonstrate knowledge of the techniques, materials, and processes involved in producing aircraft detail assemblies
Producing and preparing molten materials for castingReal unit · GQA Qualifications Limited
This unit covers the production and preparation of molten materials for casting. You'll control temperatures, operate equipment safely, monitor material properties, and understand material types and temperature importance.
What you'll be able to do
- Produce and prepare molten materials for casting in accordance with specified procedures.
- Understand the processes involved in producing and preparing molten materials for casting.
Producing and preparing sand moulds and cores for castingReal unit · GQA Qualifications Limited
You'll learn to produce and prepare sand moulds and cores for casting. The unit includes preparing sand mixtures, producing moulds and cores using appropriate techniques, and correctly setting cores into moulds to meet dimensional and surface finish requirements.
What you'll be able to do
- Produce and prepare sand moulds and cores for casting, ensuring dimensional accuracy and surface finish requirements are met
- Demonstrate knowledge of the procedures involved in producing and preparing sand moulds and cores for casting, including sand mixing, mould making, and core setting techniques
Producing cast components by manual meansReal unit · GQA Qualifications Limited
You'll develop the skills to produce cast components manually to specified dimensions and tolerances while adhering to safe working practices. The unit covers identification and rectification of defects, different casting processes, and the properties of casting materials.
What you'll be able to do
- Produce cast components by manual means to the required specification
- Demonstrate knowledge of the processes involved in producing cast components by manual means
Producing components by rapid prototyping techniquesReal unit · GQA Qualifications Limited
You'll produce components using rapid prototyping techniques, selecting appropriate methods and operating equipment safely. The unit includes producing components to specifications and inspecting them for defects and accuracy.
What you'll be able to do
- Produce components using rapid prototyping techniques according to specifications.
- Evaluate the quality and accuracy of components produced by rapid prototyping techniques.
- Understand the principles of producing components by rapid prototyping techniques.
- Understand the methods for evaluating the quality and accuracy of components produced by rapid prototyping techniques.
Producing components using hand fitting techniquesReal unit · GQA Qualifications Limited
It teaches you to produce components using hand fitting techniques to meet specified dimensions and quality standards. You'll use appropriate tools safely and check the accuracy of finished components, gaining knowledge of various hand fitting methods.
What you'll be able to do
- Produce components using hand fitting techniques to meet specified requirements
- Demonstrate knowledge of the techniques and processes involved in producing components using hand fitting techniques
Producing composite assembliesReal unit · GQA Qualifications Limited
You'll develop the ability to produce composite assemblies by selecting suitable materials, preparing them according to requirements, and using appropriate equipment. The unit also covers the production process following specified procedures to meet quality standards.
What you'll be able to do
- Prepare materials and equipment for the production of composite assemblies
- Produce composite assemblies according to specified procedures and quality standards
- Demonstrate knowledge of composite materials and their properties
- Demonstrate knowledge of the production techniques for composite assemblies
Producing composite mouldings using pre-preg techniquesReal unit · GQA Qualifications Limited
This unit focuses on producing composite mouldings using pre-preg laminating techniques. You'll prepare pre-preg materials, apply laminates to moulds, cure the mouldings according to procedures, and inspect finished products for defects.
What you'll be able to do
- Produce composite mouldings using pre-preg laminating techniques, following established procedures and safety guidelines
- Describe the pre-preg laminating techniques used in producing composite mouldings
- Explain the importance of following safety guidelines when working with pre-preg materials
Producing composite mouldings using wet lay-up techniquesReal unit · GQA Qualifications Limited
You'll develop the ability to produce composite mouldings using wet lay-up techniques. The unit covers preparing moulds and materials, applying resin and reinforcement, curing mouldings, and ensuring the finished product meets strength and finish requirements.
What you'll be able to do
- Produce composite mouldings using wet lay-up techniques according to specifications
- Prepare moulds and materials for wet lay-up processes
- Apply resin and reinforcement materials using wet lay-up techniques
- Cure and finish composite mouldings produced using wet lay-up techniques
Producing electrical or electronic engineering drawings using a CAD systemReal unit · GQA Qualifications Limited
This unit covers producing electrical or electronic engineering drawings using CAD software, applying relevant standards and conventions. You'll gain skills in creating accurate, clear, and complete drawings, alongside understanding CAD software functions specific to electrical and electronic engineering.
What you'll be able to do
- Produce electrical or electronic engineering drawings using a CAD system, adhering to relevant standards and conventions.
- Produce electrical or electronic engineering drawings using a CAD system, including understanding CAD software functions and drawing conventions.
Producing engineering project plansReal unit · GQA Qualifications Limited
It teaches you to produce engineering project plans that meet specified requirements. You'll define project scope, objectives, resources, and timelines, and present plans clearly to stakeholders to support project delivery.
What you'll be able to do
- Produce engineering project plans that meet specified requirements
- Define project scope, objectives, and deliverables
- Identify resources, tasks, and timelines for engineering projects
- Document and communicate engineering project plans effectively
Producing mechanical assembliesReal unit · GQA Qualifications Limited
You'll be able to produce mechanical assemblies by interpreting engineering drawings and specifications. The unit covers preparing components, assembling to specified tolerances and fits, and ensuring the final assembly meets performance criteria.
What you'll be able to do
- Produce mechanical assemblies according to engineering drawings and specifications
- Prepare components for assembly, ensuring correct alignment and fit
- Use appropriate tools and techniques to assemble mechanical components
- Check the completed assembly for accuracy and functionality
Producing mechanical engineering drawings using a CAD systemReal unit · GQA Qualifications Limited
You'll produce mechanical engineering drawings using CAD software, applying appropriate commands, dimensions, tolerances, and annotations. The unit also covers saving and printing drawings in suitable formats.
What you'll be able to do
- Produce mechanical engineering drawings using a CAD system to meet specified requirements
- Describe the procedures for producing mechanical engineering drawings using a CAD system
- Explain the importance of accuracy and detail in mechanical engineering drawings
Producing platework components and assembliesReal unit · GQA Qualifications Limited
You'll produce platework components and assemblies to specified dimensions and tolerances using appropriate cutting and shaping tools. The unit covers defect identification, safe working practices, and the use of joining techniques to ensure structural integrity.
What you'll be able to do
- Produce platework components to meet specified requirements
- Produce platework assemblies to meet specified requirements
- Know the techniques used to produce platework components
- Know the techniques used to produce platework assemblies
Producing sheet metal components and assembliesReal unit · GQA Qualifications Limited
It teaches you to produce sheet metal components and assemblies to specified dimensions and tolerances. You'll apply appropriate fabrication and assembly techniques, inspect finished assemblies for defects, and understand material properties and safety considerations.
What you'll be able to do
- Produce sheet metal components and assemblies to the required specification
- Demonstrate knowledge of the processes involved in producing sheet metal components and assemblies
Stripping and rebuilding motorsport engines pre-competitionReal unit · GQA Qualifications Limited
You'll gain skills to strip and rebuild motorsport engines pre-competition. The unit includes dismantling engines, inspecting components for defects, reassembling to manufacturer specifications, and testing to ensure correct operation.
What you'll be able to do
- Strip and rebuild motorsport engines in preparation for competition, following established procedures and safety guidelines
- Demonstrate knowledge of the procedures involved in stripping and rebuilding motorsport engines pre-competition, including component identification, inspection, and reassembly techniques
Stripping and rebuilding motorsport vehicles pre-competitionReal unit · GQA Qualifications Limited
You'll strip and rebuild motorsport vehicles pre-competition following established procedures. The unit covers component identification, safe storage, and reassembly to required specifications with correct torque application.
What you'll be able to do
- Strip motorsport vehicles in preparation for pre-competition checks and rebuild.
- Rebuild motorsport vehicles to the required specification following pre-competition checks.
- Understand the procedures for stripping motorsport vehicles pre-competition.
- Understand the methods for rebuilding motorsport vehicles to the required specification.
Using and communicating technical informationReal unit · GQA Qualifications Limited
It teaches you to extract, interpret, and apply technical information within engineering contexts. You'll learn to communicate technical data clearly and accurately through written and oral presentations.
What you'll be able to do
- Use technical information effectively in a relevant engineering context
- Communicate technical information clearly and accurately in a relevant engineering context
- Describe the methods used to communicate technical information
- Explain the importance of using and communicating technical information accurately
Using computer software packages to assist with engineering activitiesReal unit · GQA Qualifications Limited
You'll develop skills in using computer software packages to assist with engineering activities such as creating drawings or models, analysing data, and generating reports. The unit also covers understanding different software types and their applications within engineering contexts.
What you'll be able to do
- Use computer software packages to assist with engineering activities effectively.
- Understand how computer software packages can be used to support various engineering activities.
Using wood for pattern, modelmaking and other engineering applicationsReal unit · GQA Qualifications Limited
You'll learn to use wood for pattern making, modelmaking, and other engineering applications. The unit covers selection of appropriate wood types, shaping and joining techniques, and producing components to specified requirements.
What you'll be able to do
- Use wood for pattern making, modelmaking and other engineering applications, selecting appropriate wood types and techniques
- Describe the properties of different types of wood used in pattern making, modelmaking and other engineering applications
- Explain the importance of selecting the correct wood type for a specific application
Wiring and testing electrical equipment and circuitsReal unit · GQA Qualifications Limited
This unit develops learners' skills to wire and test electrical equipment and circuits safely and to industry standards. You'll interpret wiring diagrams, apply safety regulations during wiring, and use testing equipment to verify functionality and compliance.
What you'll be able to do
- Wire electrical equipment and circuits according to industry standards and safety regulations
- Test electrical equipment and circuits to ensure correct functionality and safety
- Describe the procedures for wiring and testing electrical equipment and circuits
- Explain the importance of following safety regulations when working with electrical equipment
Wiring and testing programmable controller based systemsReal unit · GQA Qualifications Limited
This unit equips learners with the skills to wire and test programmable controller based systems according to schematics and industry safety standards. You'll understand the function of system components and the procedures necessary to ensure correct system operation.
What you'll be able to do
- Wire and test programmable controller based systems in accordance with industry standards
- Demonstrate knowledge of the wiring and testing procedures for programmable controller based systems
Working safely in an engineering environmentReal unit · GQA Qualifications Limited
You'll gain knowledge and skills to work safely in an engineering environment by identifying hazards, assessing risks, and implementing control measures. The unit covers adherence to health and safety regulations, organisational procedures, and correct use of safety equipment.
What you'll be able to do
- Work safely in an engineering environment, adhering to relevant health and safety regulations and organisational procedures.
- Work safely in an engineering environment, taking into account potential hazards and risks.
- Demonstrate knowledge of how to work safely in an engineering environment, including the identification of hazards and the implementation of control measures.
- Demonstrate knowledge of how to work safely in an engineering environment, understanding emergency procedures and the use of personal protective equipment (PPE).
The honest bit
You’ve started things before
Most courses were built for a room full of people who aren’t you. A cohort moves on whether or not your week allowed it, and by the third week the thing you’re behind on becomes the reason you stop opening it.
There’s no cohort here, and no timetable to fall behind. Before anything starts, Zavmo asks when you’re sharpest and how long you can realistically sit down for, then builds the sessions around those answers. A bad fortnight changes your pace. It doesn’t put you behind.
And you only pay once you start learning. Searching and planning are free, and you can cancel any time — so the cost of finding out is an afternoon, not a year.
Your passport
Every credit is a stamp you keep
Level 2 credits are regulated. They don’t vanish when a subscription ends or a website closes. They travel to any employer, and Zavmo keeps the map of what you’ve earned and what’s next.
Assembling Structural Sub Assemblies to Produce a Public Service VehicleAssembling and testing electronic circuitsAssembling and testing fluid power systemsAssembling pattern, model and engineering woodwork componentsAssembling, wiring and testing electrical panels/components mounted in enclosuresCarrying out aircraft detail fitting activitiesCarrying out engineering activities efficiently and effectivelyCarrying out hand forging of engineering materials
Each stamp is a real unit registered against this qualification.
Who’d teach you this
The Evidence Evaluator
Assessor
Helps you show what you can actually do, gathering the evidence that proves it as you learn.
Meet all twelve tutorsWhere this connects
Where these credits take you
A qualification is never a dead end here. See the jobs its credits open, the national occupational standards its units map to, and the future skills they quietly build.
GQA PAA\VQ-SET Level 2 NVQ Diploma in Performing Engineering Operations
- Applying Surface Treatments
- Assembling Engineering Woodwork Components
- Assembling Structural Sub Assemblies to Produce a Public Service Vehicle Legacy
- Assembling and Testing Fluid Power Systems Legacy
- Assembling and testing electronic circuits
- Assembling and testing electronic circuits Legacy
- Assembling and testing fluid power systems
- Assembling furniture and structural units for leisure vehicles
Skills it covers
What the job actually needs. These are the standards the units are built against, in the words employers and awarding bodies already use for the work itself.
Applying Surface TreatmentsAssembling Engineering Woodwork ComponentsAssembling Structural Sub Assemblies to Produce a Public Service Vehicle LegacyAssembling and Testing Fluid Power Systems LegacyAssembling and testing electronic circuitsAssembling and testing electronic circuits LegacyAssembling and testing fluid power systemsAssembling furniture and structural units for leisure vehiclesAssembling pattern, model and engineering woodwork componentsCarry out basic electrical tests and repairs on motorsport vehiclesCarrying out aircraft detail fitting activitiesCarrying out evolutionary operations (EVOP)Carrying out hand forging of engineering materials LegacyCarrying out maintenance activities on motorsport vehicle electrical equipmentConducting Business Improvement ActivitiesCutting and shaping materials using thermal cutting equipmentFinishing surfaces by applying coatings or coverings LegacyFinishing surfaces by applying treatments Legacy+70 more
How you’ll actually learn this
One-to-one, on your own real work
A qualification is usually something done to you: sit the class, sit the exam, hope it sticks. Here it’s the opposite. You learn it one-to-one with a companion, on your own real work, and you keep going until you can use it, not just recall it.
One-to-one, on your real workNo lectures, no past-papers. Every unit is practised on the actual tasks your job throws at you, a tutor beside you, not a video in front of you.
Taught to the top, not the testMost courses stop at remembering. Your companion keeps climbing: analysing, judging, creating. That’s the part a machine can’t do for you.
Credits you keep, a map that continuesEvery unit is regulated and yours for good. The day you finish, Zavmo already knows the next role your new credits open.
Applied to your own work
Learners will develop the skills to assemble structural sub-assemblies for public service vehicles according to specified drawings and instructions. The unit includes ensuring quality standards are met and understanding the function and importance of different structural components.
How the thinking builds
- Remember
- Understand
- Apply
- Analyse
- Evaluate
- Create
Built for GQA PAA\VQ-SET Level 2 NVQ Diploma in Performing Engineering Operations
73 units in this credential, in the order it lists them, awarded by GQA Qualifications Limited.
- Assembling Structural Sub Assemblies to Produce a Public Service Vehicle
- Assembling and testing electronic circuits
- Assembling and testing fluid power systems
- Assembling pattern, model and engineering woodwork components
- Assembling, wiring and testing electrical panels/components mounted in enclosures
- Carrying out aircraft detail fitting activities
and 67 more in the full unit list below.
One to one, not one to many
No two people run this the same way
A course is written once and handed to everyone. This is assembled around you, and keeps changing as it learns you. Five things it reads, and what each one changes.
- Your actual work Every unit is taught against a live piece of your own work, not a worked example from a textbook.
- What you already know The first conversation finds your starting point, so you skip what you can already do and spend the time on what you cannot.
- The conditions you learn under Not a learning-styles quiz. The evidence does not support those. The dimensions the research does back, read once and used to shape the plan.
- How far you got last time It picks up mid-thought. The tutor knows what you said, what you struggled with, and what it asked you to try.
- Which tutor suits the moment Twelve of them, each for a different kind of thinking. The one who walks you through a first idea is not the one who stress-tests it.
See how you learn, free. Eight questions, no sign-up. A directional taster; the diagnostic inside Zavmo goes deeper and keeps adapting.
Why it sticks
Most courses stop at remembering
There’s a well-known ladder of how deeply you learn something, called Bloom’s Taxonomy. Most courses get you up the first two rungs: you remember some facts, you pass a test, you forget it. Real skill lives at the top. Judging, deciding, creating. And this isn’t a generic ladder: every rung has a named Zavmo tutor who walks you up it.
- 6CreateThe Creative Catalyst
- 5EvaluateThe Evidence Evaluator
- 4AnalyseThe Analyst
- 3ApplyThe Coach
- 2UnderstandThe Connector
- 1RememberThe Builder
Where most courses leave you Where Zavmo takes you
Why this matters: AI can already remember and understand for you. What it can’t do is
take your real problem and judge the right call. So the only learning worth paying
for is the learning that takes you to the top. That’s exactly what a tutor doing it with
you, on your real work, is for.
The value
Why the companion is worth £70 a month
You’re not paying for the units. They’re regulated, and the same wherever you earn them. You’re paying for the one thing that decides whether you actually get there: a companion that makes them stick, on your real work.
That is one-to-one on this qualification, every day, on the work you already do, for £70 a month. Your first module is free, so you can see the teaching before you pay for any of it. Billed monthly, cancel any time and billing stops.
Earned on your own work, taught to the top.
Everything you just read, learned one-to-one on the job you already do. Your first module is free, so you can see the teaching before you pay for any of it.
Build my plan, freeNo card. See how this qualification maps onto your role and meet the tutors who’d teach it, free. The learning begins when you subscribe. It’s £70 a month, billed monthly. Cancel any time and billing stops.